Fusion Windows and Doors Logo

Case Study · Beverly Hills, CA 90210

Benedict Canyon: 28 Milgard C700 Doors & Windows

  • Full C700 fiberglass package: 28 Milgard C700 French doors and C700 casement windows across the entire home
  • Block frame replacement: original frames removed to the rough opening so the new units sit square and seal properly
  • White on white with black HOPPE hardware: matching interior and exterior finish, with black HOPPE levers and handle sets throughout

Project At a Glance

Location
Benedict Canyon, Beverly Hills, CA 90210
Product
Milgard C700 Fiberglass
Scope
28 French doors & casement windows
Install Method
Block frame replacement
Finish
White exterior / white interior
Hardware
Black HOPPE
Installer
Fusion in-house crew

28

C700 Doors & Windows Installed

90210

Benedict Canyon, Beverly Hills

0

Subcontractors — All In-House

Benedict Canyon Project Snapshot

Scope of Work

Product Line: Milgard C700 Ultra™ Series fiberglass

Units: 28 total — C700 French doors paired with C700 casement windows

Installation: Block frame replacement, existing frames
removed down to the rough opening, new frames set, shimmed, flashed, and sealed

Color: White on white (white exterior, white interior)

Hardware: Black HOPPE handle sets and levers on all operable doors and windows

Extras: Interior and exterior trim finishing, full haul-away of old units

Location & Service Area

Neighborhood: Benedict Canyon, Beverly Hills, CA

Zip Code: 90210

Nearby Areas We Serve: Beverly Hills, Bel Air, Sherman Oaks, Studio City, West Hollywood, Encino

From Our Showroom: 479 W. Riverside Dr., Burbank, CA 91506, roughly 20 minutes over the canyon

Code Compliance: All units meet California Title 24 energy requirements

License: California Contractors License #956355

The Story Behind the Benedict Canyon Job

Benedict Canyon homes sit in a pocket of Beverly Hills where the canyon walls trap heat in the afternoon and drop the temperature fast after sundown. The older aluminum and single-pane units common to these
houses cannot keep up with that swing, and the sliding doors that open onto canyon-facing patios are usually the worst offenders.

This homeowner came to our Burbank showroom with a whole-house replacement in mind: every window and every exterior door, done once, done right, with a single look carried through the entire property. They wanted French doors instead of sliders on the main living spaces, casement windows for maximum ventilation on the canyon side, and a crisp white frame that would read clean against the exterior stucco.

The detail that pulled it together was the hardware. Black HOPPE levers and handle sets against white fiberglass gave the house the contrast it needed without changing the frame color, a small decision that shows
up in every room.

The Problem

The home's original windows and doors were failing on every front: drafts at the frames, hard-to-operate sliders on the patio openings, and afternoon heat gain the HVAC could not keep ahead of. With 28 openings across the property, patchwork repairs were no longer worth the money, and the homeowner wanted a single consistent look rather than a mix of styles accumulated over the years.

The Solution

We specified the Milgard C700 fiberglass line across the board, C700 French doors on the main openings and C700 casement windows everywhere else. Every unit was installed using block frame replacement, which strips the old frame back to the rough opening so the new one seats square and seals properly. Finish was white on white with black HOPPE hardware. As an authorized Milgard dealer, we placed the order, and our own licensed crew handled demo, install, and finish work.

The Result

Twenty-eight new Title 24-compliant fiberglass units, matched in color and hardware from the front entry to the back patio. The French doors swing open onto the canyon views the sliders never framed properly, the casements pull cross-ventilation through the house on cool evenings, and the homeowner reported a noticeably steadier indoor temperature through the afternoon.

How We Ran This Project

The same four-step process we use on every Los Angeles window and door replacement, from the first canyon visit to the final walkthrough.

On-Site Measure in Benedict Canyon

We visited the property, measured all 28 openings, checked each rough opening for square, and flagged the two patio walls that would need extra prep before demo.

Product & Hardware Selection

Walked the homeowner through the C700 line in our Burbank showroom, confirmed white on white, and matched black HOPPE handle sets and levers across every operable unit.

Block Frame Replacement

Our in-house crew removed the old frames to the rough opening, set and shimmed each new unit, then flashed, sealed, and finished the interior and exterior trim.

Walkthrough & Warranty

We tested every door swing, latch, and casement crank with the homeowner, cleaned the site, hauled the old units away, and registered the Milgard warranty.

Project Gallery

Milgard C700 French doors and casement windows on the Benedict Canyon home,  white on white with black HOPPE hardware.

Planning a Similar Project in Beverly Hills?

Whether it’s a single French door or all 28 openings in the house, we start the same way: a free in-home visit, precise measurements, and a written estimate with no hidden fees.

We’re an authorized dealer for Milgard, Andersen, Marvin, Fleetwood, LaCantina, Velux, and Windsor, and every installation is handled by our own licensed, insured crew.

California Contractors License #956355

Leading dealer for Milgard, Andersen, Fleetwood, Marvin, LaCantina, Velux & Windsor.

Working Hours